Help & guides
Fitting instructions
Every PREMIUMMATTEN product is fitted in a few minutes – no tools, no garage. Choose your product and follow the steps.
Something doesn't fit or you're stuck? Write to us – we usually reply on the same working day: hilfe@premiummatten.shop
Under 5 minutes to a luxury interior
Tailored to your car model, with raised edges and waterproof. Lay them in, fix them with the adhesive strips supplied – done.
1Move both front seats all the way back – so you have enough room for fitting.
2Take out the existing mats and give the car floor a quick clean if needed.
3Lay the mat precisely in place and press the pre-cut adhesive strips firmly onto the contact points.
4Repeat the same step on the passenger side – line up and press down.
5Slide both seats back into your preferred driving position.
6Lay in the rear mats and push the fasteners under the seats. Tip: lift the seats briefly.
Safety check before your first drive: all pedals must move completely freely. Press the accelerator, brake and, if fitted, clutch all the way down several times – no adhesive tape in the pedal area.
Creases after delivery? To make sure your mats arrive safely, they are packed folded flat – this can leave visible pressure marks along the folds. Lay the mat out flat for 2–4 days, ideally at 22 °C or above; in most cases the marks will smooth out noticeably. If a crease is still visible, email us at support@premiummatten.shop – and we'll take a look at it together.
Lay in, press down, done
The metal eyelet clicks onto the factory retaining pin – no tools, no drilling, no readjusting. Honeycomb or diamond texture, tailored to your model.
1Move both front seats all the way back – so you can easily reach the whole footwell.
2Take out the old mats and give the footwell a quick hoover if needed.
3Lay the mat flat in the driver's footwell and press the metal eyelet firmly over the retaining pin until it sits in place.
4Lay it in here too and – if there is one – press it over the retaining pin. The raised edge faces upwards.
5Lay the rear mat flat in the rear footwell and line it up. Then move the seats back into position.
6With the complete set: lay the mat in and push it to the edges – the raised edge keeps dirt and moisture in.
Safety check before your first drive: if your car has retaining pins, the eyelet must sit firmly on them. All pedals must move completely freely – press the accelerator, brake and, if fitted, clutch all the way down several times.
Clean in seconds: take out, shake out, put back. Whatever sits in the cells falls out when you shake the mat – the rest comes off with water, even with a garden hose. Dries in minutes, without stains or water marks.
A new interior in 5 minutes
Fitted cover by cover – no tools, no garage. Airbag-compatible thanks to the special side seam, wipe-clean and in 15 colour options.
1Press the release button and pull the headrest upwards. It goes back on at the end.
2Pull the cover over the backrest from the top, centre the quilted seams and smooth it down.
3Guide the fastening straps through the gap between backrest and seat cushion to the back – flat and untwisted.
4Lay on the seat cushion cover and tuck the side flaps into the gap between seat cushion and backrest.
5Hook the straps together under the seat and pull them tight. The cover should sit without creases, but not be stretched.
6Pull the small cover over like a hood and push the headrest back into the backrest until it clicks into place.
Safety check before your first drive: the side airbag seams on the backrest must remain exposed – never cover them or sew them shut. If the airbag deploys, the seam opens in a controlled way and the airbag inflates unhindered.
Rear seats with the complete set: lay on the seat cushion cover and tuck the flaps into the gap, pull on the backrest cover and guide the straps through the gap to the back. Pull the seat belt buckles through the openings provided.
Stuck?
Tell us briefly what it's about – ideally with your car model and a photo. We usually get back to you on the same working day.